MICRONIX PC/104
POWER SUPPLY
PV-1075 & PV-1075-CAR
NiMH battery pack with charger
for PV-5127
User Manual
&
Installation Guide
VERS. 1.3
DOC: M5247DM.REV1.3
Micro Technic A-S • Denmark •
Tel. +45 6615 3000 • Fax +45 6615 3077
E-mail: support@micro-technic.com
Website: www.micro-technic.com
Users Manual & Installation Guide
PV- 1075: NIMH BATTERY PACK WITH CHARGER
Revision history
Revision number
Reason for change
Date
1.0
1.1
1.2
1.3
Initial revision
05-Apr-04
Added PV-1075-car version
Changed front page
Changed “discharge current”
06-Dec-05
07-Apr-18
07-Dec-03
Page 3 of 9
Users Manual & Installation Guide
PV- 1075: NIMH BATTERY PACK WITH CHARGER
General information
Ordering codes
PV-1075-S
S=Stack-through PC/104 connector
Available models:
Model
Ordering Description
code
PV-1075-S
016.104.005 NiMH battery pack with charger.
PV-1075-S-CAR
016.104.093 NiMH battery pack with charger for mobile applications.
Accessories
This accessories must be ordered separately if needed.
Model no
Ordering code
Description
PV-1075-NH12 155.104.000
Battery pack
Page 4 of 9
Users Manual & Installation Guide
PV- 1075: NIMH BATTERY PACK WITH CHARGER
Description
Micronix PV-1075 is a back-up module with Nickel-Metal-Hydride batteries and integrated
charger. PV-1075 is designed to support the Micronix PV-5127, a high power PC/104 UPS power
supply.
Micronix PV-1075 is a high capacity battery pack for your PC/104 system. An integrated timer
controls the charging modes: standard charge and trickle charge. This timer also has the purpose to
avoid overcharging.
PV-1075 will withstand extended temperatures and the shock and vibration of mobile equipment.
PV-1075-CAR is a special version which can be used in mobile application. This version can be
operated from a 12V car battery.
Block Diagram
DC/DC
Converter
Timer
f1/32
f1
D9
D4
J1
+
-
Micronix PV-1075 is a PC/104 module that contains a NiMH battery pack, a timer controlled
charger and four connectors.
The battery pack is secured to the PCB by a fastener and electrically connected to the PCB by a two
pole connector. The battery is equipped with a polymer fuse that will disconnect the battery in case
the battery temperature becomes too high.
Page 5 of 9
Users Manual & Installation Guide
PV- 1075: NIMH BATTERY PACK WITH CHARGER
Connectors
The PV-1075 is equipped with four connectors:
Input connector (KL2)
Power into PV-1075 is supplied through KL2 that is a two-pole removable screw clamp connector.
The layout of this connector is shown on the connection drawing above. The voltage used must be
in the interval of 18-36V DC (PV-1075-CAR: 10.8V – 13.2V).
Output connector (KL1)
Mains power and battery power can be drawn from connector KL1 that is a three-pole removable
screw clamp connector. If used as a back-up module for Micronix PV-5127, this connector must be
connected to the power input connector (KL2), on PV-5127, as shown on the connection drawing
above.
Page 6 of 9
Users Manual & Installation Guide
PV- 1075: NIMH BATTERY PACK WITH CHARGER
Battery connector (J1)
The NiMH battery is connected to PV-1075 using J1 that is a two-pole MOLEX connector. The
battery connector is disconnected at delivery to prevent deep discharge of the battery when not used
for a longer period.
PC/104 connector (CN1)
PV-1075 is attached the PC/104 stack using CN1. There are no electrical connection to this
connector and serves only to bypass the PC/104-bus in the stack.
Battery charger
The battery charger controls the charging process using two modes:
• standard charge mode with charging current = 50mA and
• trickle charge mode with charging current = 25mA.
The switching between these modes is determined by a counter which is controlled by the
‘presence’ of mains. There are two input frequencies to this counter: one used during the presence
of mains input and one used when there are no mains input. The two frequencies have a mutual
ratio of 32 where the lowest frequency is used during count-up. During the presence of mains, the
counter counts up. When mains disappear, the counter counts down. The charging progress is
illustrated below:
Charging indicators
Two LEDs indicate the actual charging mode: D4 (yellow) indicate Standard Charge and D9
(green) indicate Trickle Charge. These LEDs are located on the component side.
Page 7 of 9
Users Manual & Installation Guide
PV- 1075: NIMH BATTERY PACK WITH CHARGER
Technical data
Mains input:
Input voltage:
PV-1075
18 – 36Vdc
10.8 – 13.2Vdc
PV-1075-CAR
Input current:
Standard charge: 69mA @ Vin=24Vdc
Trickle charge: 43mA @ Vin=24Vdc
Standard charge: 115mA @ Vin=12Vdc
PV-1075
PV-1075-CAR
Trickle charge:
64mA @ Vin=12Vdc
Battery charger:
Charging modes:
Standard charge: 50mA
Trickle charge: 25mA
Charging time:
Charge counter:
Standard charge: 12hrs
Trickle charge: continuous
Counting 0 -> Max.: approx.12hrs.
Counting Max. -> 0: approx. 23min.
Battery:
Battery voltage:
Battery type:
Number of cells:
Battery capacity:
Recommended discharge current(max):
Battery protection:
Environmental:
12V typical
NiMH
10pcs.
500mAH
750mA
polymer fuse
Temperature range by Standard charge:
Temperature range by discharge:
Storage temperature:
Humidity:
Cyclic humidity:
Vibration:
Sustained vibration:
Shock:
Weight:
0 to 70°C
-10 to 70°C
-20 to 30°C
20 to 90% non-condensing
ETS 300 019-2-5 or equal
10-1000 Hz sinus and random @ 1-1.5G RMS
EN 60068-2-34 & 60068-2-36
IEC 60068-2-27 & 60068-2-29
185g
Size (WxLxH)
90 x 96 x 15
Page 8 of 9
Users Manual & Installation Guide
PV- 1075: NIMH BATTERY PACK WITH CHARGER
Mechanical layout
The schematic on this page shows the dimensions for PV-1075.
All dimensions are in mm.
Page 9 of 9
|
Lantronix Network Router WiSpan User Manual
Lexmark Printer X730 User Manual
Link electronic Stereo Amplifier DigiFlex 1651 User Manual
Magnavox DVD VCR Combo 1VMN26714 User Manual
Makita Cordless Drill BDF442 BDF452 User Manual
Mamiya Film Camera 645 PRO TL User Manual
Manitowoc Ice Ice Maker 7628973 User Manual
M Audio Headphones gd_060903 User Manual
Maytag Washer W10446215 User Manual
Meyer Sound Portable Speaker Stella 4 User Manual